Best Quality D-VXR-DY-23 Exam Questions EMC Test To Gain Brilliante Result!
Preparations of D-VXR-DY-23 Exam 2026 Storage Administrator Unlimited 375 Questions
NEW QUESTION # 85
You are performing a troubleshooting steps on a 4 node VxRail cluster. The cluster uses Erasure Coding for all VMs. When you attempt to put a node into maintenance modeusing the recommended vSAN data migration policy, the operation fails.
What could be done to successfully put the node into maintenance mode?
- A. Storage vMotion the VMs off the node
- B. Cold migrate the VMs off the node
- C. Use the 'Full Data Migration' option
- D. Use the 'No Data Migration' option
Answer: C
NEW QUESTION # 86
Which VxRail configurations can be reviewed using the As-Built Configuration Report at the time the report is generated?
- A. Node models, license keys, vSAN VLAN ID, and vMotion VLAN ID
- B. vMotion interface IP addresses, vCenter users and passwords, and opened firewall ports
- C. Node PSNT numbers, license activation dates, and Private Management Network VLAN ID
- D. Node names, vSAN interface IP addresses, and VxRail Manager users and passwords
Answer: A
NEW QUESTION # 87
Which vSAN license is included with VxRail?
- A. vSAN Advanced
- B. vSAN Standard
- C. vSAN Enterprise
- D. vSAN for ROBO
Answer: C
NEW QUESTION # 88
When validating the completed VxRail PEQ, you note the following VLANs in the configuration:\
- VxRailManagement - VLAN 120
- vSAN - VLAN 121
- vMotion - VLAN 122
- Servers - VLAN 204
- NetManagement - VLAN 208
Which command should you use to validate that the VLANs are configured on each Dell EMC ToR switch?
- A. show vlan
- B. show interfaces port-channel brief
- C. show running-config spanning-tree
- D. show interfaces status
Answer: A
NEW QUESTION # 89
What is the maximum number of hosts supported in a VxRail Stretched Cluster?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: B
NEW QUESTION # 90
A VxRail Cluster has just been deployed. Use the VxRail simulator to determine the Service Tag, Model, and ESXJ IP Address of the first node - vcluster730.esx01.edu.local. Note: It is necessary to dose (x) the simulator window before you can select a response to this question.
- A. Option B
- B. Option D
- C. Option A
- D. Option C
Answer: B
NEW QUESTION # 91
A Dell EMC solutions architect has updated the VxRail PEQ with Customer Top-of-Rack (ToR) switch details.
On which worksheet would they need to be to generate a new NVT JSON file?
- A. Networking Details
- B. Customer
- C. VxRail Cluster
- D. Engagement Details
Answer: C
NEW QUESTION # 92
Which vSAN setting is enabled by default during the initial deployment of a VxRail cluster?
- A. Encryption
- B. Deduplication and Compression
- C. Performance Service
- D. Storage policy of FTT = 1
Answer: B
NEW QUESTION # 93
Where can the latest VxRail Pre-Installation Site Checklist be obtained for a new deployment?
- A. EMC Support VxRail
- B. VxRail Master Knowledge Base article
- C. SolVe
- D. Service offering index
Answer: A
NEW QUESTION # 94
What is a requirement for the vSAN Data-at-Rest Encryption?
- A. All-Flash or AII-NVMe VxRail
- B. External Key Management Server
- C. External customer provided vCenter
- D. VxRail with at least 3 nodes
Answer: B
NEW QUESTION # 95
A customer is configuring VxRail to connect to an existing, external SRS VE. Their support account is associated with the Site ID/Party ID where VxRail is installed. A validation error is issued when the customer attempts to register VxRail in SRS.
What is the possible cause for the error?
- A. Number of deployed devices on SRS gateway has exceeded the maximum
- B. Wrong IP address was used for SRS VE gateway
- C. SRS traffic goes through a proxy server
- D. Status of VxRail in Install Base is 'Shipped'
Answer: D
NEW QUESTION # 96
What is the correct sequence of steps to perform a RASR Factory Reset using an SD card?
Answer:
Explanation:
NEW QUESTION # 97
What action is required to enable VxRail Manager the ability to update system software and browse VxRail KB articles?
- A. Set the Username and Password for the Support Account
- B. Configure Proxy settings
- C. Enable Secure Remote Support (SRS)
- D. Set the appliance status to 'Installed' in the Dell EMC Install database
Answer: A
NEW QUESTION # 98
How many cables are required to install a 4 node VxRail Model G410 cluster with 1 GbE into a rack?
- A. 20 CAT6 network cables
- B. 4 CAT6 and 32 SFP+ connectors, and 16 fiber cables
- C. 4 CAT6 and 16 Twinax network cables
- D. 4 CAT6 and 8 Twinax network cables
Answer: A
NEW QUESTION # 99
How should an administrator manually validate the DNS readiness of a customer network?
- A. Ping the default gateway of the management VLAN
- B. Run nslookup on server FQDN and IP
- C. Run a traceroute to the DNS server
- D. Generate a Network PEQ
Answer: B
Explanation:
Graphical user interface, text, application Description automatically generated
NEW QUESTION # 100
What is the default network traffic configuration for a VxRail node with 2 x 10 GbE ports?
- A. Management, vMotion, and Virtual Machines on Uplink1 vSAN on Uplink2
- B. Management and vMotion on Uplink1 vSAN and Virtual Machines on Uplink2
- C. Management, Virtual Machines, and vSAN on Uplink1 vMotion on Uplink2
- D. Management and Virtual Machines on Uplink1 vSAN and vMotion on Uplink2
Answer: A
NEW QUESTION # 101
What guideline should be followed when planning bandwidth between sites hosting VM objects and the witness nodes?
- A. 1500 MTU on the VSAN vmkernel interface
- B. 5 ms with a recommended minimum bandwidth of 10Gbps
- C. 500 ms roundtrip (< 250 ms one way)
- D. 2 Mbps for every 1000 objects on the vSAN
Answer: D
NEW QUESTION # 102
......
Focus on D-VXR-DY-23 All-in-One Exam Guide For Quick Preparation: https://realtest.free4torrent.com/D-VXR-DY-23-valid-dumps-torrent.html