BICSI OSP-002 Real Exam Questions Test Engine Dumps Training With 170 Questions
OSP-002 Actual Questions Answers PDF 100% Cover Real Exam Questions
To become certified, professionals must pass a comprehensive exam that covers the key concepts and principles of outside plant design. OSP-002 exam consists of 100 multiple-choice questions and is designed to test the knowledge and skills of professionals who work in the field of outside plant design.
BICSI OSP-002 exam is a comprehensive certification examination that evaluates the knowledge and skills required for designing and installing outside plant infrastructure. OSP-002 exam is ideal for individuals who work in the telecommunications industry and have a strong background in outside plant design and installation. The OSP-002 certification provides individuals with the knowledge and skills required to design and install outside plant infrastructure that is reliable, efficient, and cost-effective.
NEW QUESTION # 11
A wireless antenna is also known as a \_\_\_\_\_\_\_\_\_\_.
- A. Access point
- B. Hot spot
- C. Wireless router
- D. WC (wireless cell)
Answer: A
NEW QUESTION # 12
Gigabit Ethernet uses all four pairs of a UTP cable \_\_\_\_\_\_\_\_\_.
- A. Bidirectionally
- B. For power
- C. Simultaneously and bidirectionally
- D. With 2 pairs in each direction
Answer: C
NEW QUESTION # 13
What other cables are recognized in the structured cabling standards?
- A. Singlemode and multimode fiber optic cable
- B. Multimode fiber optic cable
- C. IBM Type II
- D. CATV RG-6 coax
Answer: A
NEW QUESTION # 14
Long wavelength singlemode links at wavelengths in the range of 1300-1650 nm links must use __________ detectors in the receiver for the best sensitivity performance.
- A. Silicon
- B. InGaAs
- C. Germanium
Answer: B
NEW QUESTION # 15
The difference between a fiber optic connector and a splice is __________.
- A. Connectors are demountable, while splices are permanent
- B. Connectors are smaller than splices
- C. Splices need expensive tools
- D. Connectors require adhesives
Answer: A
NEW QUESTION # 16
What minimum level of UTP cable type is required by 1000Base-T (Gigabit Ethernet)
- A. Cat 6
- B. Augmented Cat 6
- C. Cat 5
- D. Cat 5e
Answer: D
NEW QUESTION # 17
Which fiber optic test instrument uses backscattered light for measurements?
- A. OTDR
- B. VFL
- C. Tracer
- D. OLTS
Answer: A
NEW QUESTION # 18
For planning office layout, each user should be allocated \_\_\_\_\_\_\_ floor space.
- A. 3 sq m
- B. Adequate
- C. 100 sq ft
- D. shared
Answer: C
NEW QUESTION # 19
The principle of operation of OTDRs is similar to \_\_\_\_\_\_\_.
- A. Lenses
- B. Mirrors
- C. Radar
- D. Power meters and sources
Answer: C
NEW QUESTION # 20
Does a jack have the same color code for the pairs as a punchdown block?
- A. Depends on whether it is T568A, T568B or USOC
- B. Depends on the type and manufacturer of the jack
- C. Yes
- D. No
Answer: D
NEW QUESTION # 21
The development of _________ provided a low cost cabling alternative for networks.
- A. Balanced transmission on UTP cabling
- B. CATV coax
- C. IBM Type 1 cable
Answer: A
NEW QUESTION # 22
The loss of a singlemode fiber is lowest at \_\_\_\_\_\_\_\_\_\_.
- A. 1550 nm
- B. 1310 nm
- C. 1300 nm
- D. 850 nm
Answer: A
NEW QUESTION # 23
From a reliability standpoint, \_\_\_\_\_\_\_\_\_\_\_\_ is the best method to join two fibers.
- A. Factory terminations
- B. Fusion splicing
- C. Adhesive/polish connectors
- D. Mechanical splicing
Answer: B
NEW QUESTION # 24
What is the maximum length of a permanently installed UTP cabling link allowed in structured cabling standards?
- A. 100 meters
- B. Depends on the electronics running on the link
- C. 100 feet
- D. 90 meters
Answer: D
NEW QUESTION # 25
The Cat 3 jack is the same as a Cat 5e/6 jack except _________.
- A. The punchdowns fit bigger wires
- B. It only connects to RJ-45 plugs
- C. It is keyed to snap into outlets upside down
- D. There are no internal twists to enhance performance
Answer: D
NEW QUESTION # 26
10 dB corresponds to a factor of \_\_\_\_\_\_\_\_\_\_ in power.
- A. 0
- B. 1
- C. 2
- D. 3
Answer: C
NEW QUESTION # 27
Individual splice loss on concatenated cables can be verified by \_\_\_\_\_\_\_\_\_\_ .
- A. Visual inspection
- B. Insertion loss testing
- C. OTDR testing
- D. Visual fault location
Answer: D
NEW QUESTION # 28
What cable types are included in the TIA-568 structured cabling standards?
- A. UTP (unshielded twisted pair) and coax
- B. UTP (unshielded twisted pair), STP (shielded twisted pair) and coax
- C. UTP (unshielded twisted pair), ScTP (screened twisted pair), STP (shielded twisted pair) and fiber optics
- D. UTP (unshielded twisted pair), ScTP (screened twisted pair) and STP (shielded twisted pair)
Answer: C
NEW QUESTION # 29
Physical contact (PC) polish on connectors is designed to reduce \_\_\_\_\_\_\_\_\_\_.
- A. Loss
- B. Loss and reflectance
- C. Reflectance
- D. Polishing time
Answer: B
NEW QUESTION # 30
What test instrument(s) are used for insertion loss testing.
- A. OLTS or light source and power meter
- B. VFL
- C. OTDR
Answer: A
NEW QUESTION # 31
What is the core size of 1300 - 1550 nm singlemode fiber?
- A. 5 mm
- B. 63.5 microns
- C. 9 microns
- D. 50 microns
Answer: C
NEW QUESTION # 32
......
BICSI OSP-002 Certification Exam consists of 100 multiple-choice questions that must be completed within a three-hour time limit. OSP-002 exam covers a wide range of topics related to outside plant infrastructure design, including site surveying, cable and conduit placement, grounding and bonding, and safety practices. OSP-002 exam also tests knowledge of industry standards and codes, such as the National Electric Code (NEC) and the Telecommunications Industry Association (TIA) standards.
Free4Torrent OSP-002 Exam Practice Test Questions: https://realtest.free4torrent.com/OSP-002-valid-dumps-torrent.html